Scaffolding Pipe

If you are planning to wholesale cheap scaffolding pipe from one of the leading scaffolding pipe manufacturers and factory,Website:http://www.czpipeline.com, please feel free to contact Cangzhou Zhongshun Steel Pipe Trade Co.,Ltd.ERW Transmission PipeERW Transmission Pipe: standard: API 5CT,API 5L, ISO 3183, EN 10217-1, Transmission Pipe: Use For conveying gas, water and oil either in the oil or natural gas industriesDimensions: No.NameStandard                                                        Grades                                                                Uses1Oil CasingAPI SPEC 5CTH40, J55, K55, N80-1For oil-gas well casing 2Line PipeAPI SPEC 5LISO 3183A, B——X80L210——L555For the pipeline transportation of oil and natural gas3Welded Steel Tubes For Pressure PurposesEN10217-1P195TR1, P195TR2, P235TR1, P235TR2, P265TR1, P265TR2Welded Steel Tubes For Pressure PurposesEnd:square ends (straight cut, saw cut, and torch cut). or beveled for welding, beveled,Surface: Lightly oiled, Hot dip galvanized, Electro galvanized, Black, Bare, Varnish coating/Anti rust oil, Protective Coatings (Coal Tar Epoxy,Fusion Bond Epoxy, 3-layers PE)Packing:Plastic plugs in both ends, Hexagonal bundles of max. 2,000kg with several steel strips, Two tags on each bundle, Wrapped in waterproof paper, PVC sleeve, and sackcloth with several steel strips, Plastic caps.Test:Chemical Component Analysis, Mechanical Properties (Ultimate tensile strength, Yield strength, Elongation), Technical Properties (Flattening Test, Bending Test, Blow Test, Impact Test), Exterior Size Inspection, Hydrostatic Test, X-ray Test.Third party inspection:SGS, BV, Lloyds etc.  WELD: OD: 21.3mm-660mm WT: 1mm-20mmChemical Analysis (%): Type of pipeClassGrade C Si Mn P S V Nb Ti max max max max max max max max WELDPLS1 L245 B 0.26-1.2-0.030.03--L290 X42 0.26-1.3-0.030.03--L320 X46 0.26-1.4-0.030.03--L360 X52 0.26-1.4-0.030.03--L390 X56 0.26-1.4-0.030.03--L415 X60 0.26-1.4-0.030.03--L450 X65 0.26-1.45-0.030.03--L485 X70 0.26-1.65-0.030.03--PLS2  L245M BM 0.220.451.20.0250.0150.050.050.04L290M X42M0.220.451.30.0250.0150.050.050.04L320M X46M 0.220.451.30.0250.0150.050.050.04L360M X52M 0.220.451.40.0250.015---L390M X56M 0.220.451.40.0250.015---L415M X60M 0.120.451.60.0250.015---L450M X65M 0.120.451.60.0250.015---L485M X70M 0.120.451.70.0250.015---L555M X80M 0.120.451.850.0250.015---Mechanical Properities:StandardClassGradeYield strength not less than (MPa)Tensile strength (MPa)Elongation(%)Y.S/T.SAPI SPEC 5L ISO 3183PLS1L245Bmin245415b-L29042min290415b-L32046min320435b-L36052min360460b-L39056min390490b-L415X60min415520b-L45060min450535b-L485X70min485570b-PLS2L245N BNmin245415b-L245M BMmax450760b0.93L290NX42Nmin290415b-L290MX42Mmax495760b0.93L320NX46Nmin320435b-L320MX46Mmax525760b0.93L360NX52Nmin360460b-L360MX52Mmax530760b0.93L390NX56Nmin390490b-L390MX56Mmax545760b0.93L415NX60Nmin415520b-L415MX60Mmax565760b0.93L450MX65Mmin450535b-max600760b0.93L485MX70Mmin485570b-max635760b0.93L555MX80Mmin555625b-max705825b0.93Toughness:StandardGradeTransverse minimum impact of Pipe bodyTransverse minimum impact of  weld (J) (J) D≤508508mm762mm914mm1219mmD<1422mmD=1422mmAPI SPEC 5L≤L415×6027(20)27(20)40(30)40(30)40(30)27(20)40(30)>L415×6027(20)27(20)40(30)40(30)54(40)27(20)40(30)≤L450×65>L450×6527(20)27(20)40(30)40(30)54(40)27(20)40(30)≤L485×70>L485×7040(30)40(30)40(30)40(30)54(40)27(20)40(30)≤L555×80 Note:(1)The values in the table be suitable for the full size standard sample.     (2)  The values inside bracket is the minimum single value, outside bracket is the average value.     (3) Test Temperature: 0°C.Available Dimension Range: Φ21.3~660*1~20mm