Click image to view original image
roof sheet roll forming machine/roof tile roll forming machine/arch sheet steel building machinery
Application:
This machine can be used for site wo Manufacture of Arch Sheet Forming Machine rking. Using this machinery can use in the construction of warehouses, workshops, hangars, and also in the production of boats, vehicles, and highway guardrails, etc.
Introduction:
The equipment consists of two parts, one is forming part, another is arching part. These two parts are sit on a mobile
The models we provided 600 series, 914 serious, 1000 series, 1220 series, 1250 series . If you have special request, we will work it out according to you. The following is a table for your reference:
|
TYPE |
Width of the coil |
Width of the formed sheet |
Thickness of the coil |
Proper span |
|
CS-600-305 |
600 mm |
305mm |
0.8-1.5 mm |
≤24m |
|
CS-914-400 |
914mm |
400mm |
0.8-1.5 mm |
≤40m |
|
CS-914-610 |
914 mm |
610 mm |
0.8-1.5 mm |
≤38m |
|
CS-914-650 |
914 mm |
650 mm |
0.8-1.5 mm |
≤28m |
|
CS-914-700 |
914 mm |
700 mm |
0.8-1.5 mm |
≤24m |
|
CS-914-750 |
914 mm |
750 mm |
0.8-1.5 mm |
≤15m |
|
CS-1000-400 |
1000mm |
610mm |
0.8-1.5mm |
≤40m |
|
CS-1000-550 |
1000mm |
610mm |
0.8-1.5mm |
≤30m |
|
CS- 1000-610 |
1000mm |
610mm |
0.8-1.5mm |
≤39m |
|
CS -1000-680 |
1000mm |
680mm |
0.8-1.5mm |
≤32m |
|
CS -1000-700 |
1000mm |
700mm |
0.8-1.5mm |
≤28m |
|
CS -1000-750 |
1000 mm |
750 mm |
0.8-1.5 mm |
≤25m |
|
CS -1000-800 |
1000 mm |
800 mm |
0.8-1.5 mm |
≤14m |
|
CS -1220-800 |
1250 mm |
800 mm |
0.8-1.5 mm |
≤42m |
|
CS-1250-800 |
1250 mm |
800 mm |
0.8-1.5 mm |
≤42m |
If you are not familar with this system, please contact us to work out the best solution for you. The features of this Arching roof are:
1.Self-support roof. There is no beams, columns or structure. The roof sheets are locked by a seaming machine.
2. Cost save. This building doesn't requires a mount of screws and bolts. But the roofing system is secure enough for construction. The beautiful roof will attract your eyes.
3. Labor save. Compared with traditional building, a small group will complete the Arching roof project in very shot time.
MAIN TECHNICAL SPECIFICATION
Cutting Material: Cr12MoV, Heat treatment
Cutting type: Hydraulic / Mechanical controlling cutting
Total motor power: 18.5 KW
Forming Power: 7.5KW
Bending Power: 4.0KW
Cutting Power: 4.0KW
Conical Power: 3.0 KW
Material of rollers: 45# steel, quenched HRC 58-62
Material of shafts: 45# steel, adjusted
Step of rollers: 14
Applicable Span: 5m~28m
The depth of the groove: 175 mm
Operating factor of the panel: 70 %
Thickness of the Panel: 0.8-1.5mm
Working Speed: Straight Sheet: 15m/minb
Arch Sheet: 13m/min
Seaming: 6m/min
Electric Standard: 380V / 50 HZ / 3 PHASES or according to your requirement
Controlling system: PLC
Project
